Computers and Electronics from the Shadetree Tech

Perform complete sweeps without the need to bring in an outside TSCM specialist.

• Full spectrum from 200 Hz to 3 Ghz, inlcuding infrared signals
• Detect Wireless & Wired Hidden Cameras
• Debug An Entire Room In Under 1 Minute
• Uses Infrared & Radio Frequency Detection Up to 6 GHz
• Handheld & Battery Operated
• Lights, Vibration, and Audible Alerts

Revolutionary Two-In-One Camera Detector Finds Both Wired & Wireless Cameras
Are you being spied on? As cameras become smaller and more hidden, finding them becomes more difficult. Not anymore with the Two-In-One RF/IR Hidden Camera Detector. This Hidden Camera Detector uses infrared and radio frequency technology to locate all cameras whether they are wired or wireless, turned on or off. Protect your privacy with this simple hand held device, which operates on 2 AAA batteries. It’s so easy-to-use, you can easily sweep an entire room for hidden cameras in under 1 minute. This counter surveillance device locates all hidden cameras in your home or office no matter how hidden they are.

Easily Find Hidden Cameras w/ This Easy-To-Use Device
Locating all the hidden cameras in your home or office has never been easier with this three-in-one device that features 4 LED lights, vibration, and an audible location alarm. As you hone in on a hidden camera, the devices’ signals will get stronger letting you know you are close. The radio frequency feature finds all wireless cameras within the most common range of 1Mhz – 6Ghz and the laser infrared feature finds wired cameras for the ultimate two-in-one experience that helps you find all hidden cameras whether they’re wired or wireless.

Trusted By Private Investigators Worldwide
Private Investigators worldwide trust the RF/IR Hidden Camera Detector to effectively debug rooms of hidden cameras. No matter how hidden the camera is, Private Investigators know that this device will locate all of them for complete privacy. Its wireless design locates all wired and wireless cameras for fast, effective sweeping.

This kit is best utilized by passing the RF probe around the surfaces of area being checked, but doing so at a very slow and steady rate, and no faster than that you would use to lay down a coat of latex paint with a four inch paint brush. The Magnetic and Infrared probes are used in a similar manner. With the VLF probe you can test all electrical outlets for carrier current covert eavesdropping devices. It can also detect and locate RF tracking transmitters which may have been installed to follow vehicles. The Acoustic Leakage Probe can be used to test both sides of walls, pipes, air ducts, and other locations where sound could leak from the area being checked and monitored by an eavesdropper with the naked ear. The Acoustic Leakage Probe, ALP700 probe also assists in the placement of acoustic noise generators and audio jammers. Additionally, it can also be used as an automatic monitor mode once a sweep has been conducted to detect and alarm on any changes while one is away. The line probe can be plugged into the auxiliary output and used to check any unknown wires and to test for possible eavesdropping activities and/or devices. The 24-hour recorder output and controls will store suspicious sounds on a standard cassette recorder (not included) while you are away.

Features:

• Protect your privacy and personal safety
• Locate wireless & wired hidden cameras
• Detects functioning & non-functioning hidden cameras
• Vibration warning mode
• 4 LED indicators to determine signal strength
• Sensitivity tuner

Multi-Functional Utility

The CPM700 comes with probes to detect RF transmitters (audio and video), carrier current transmitters, and telephone bugs. Probes are also available to detect infrared transmitters, tape recorders, and acoustic leakage.

Wideband Coverage

Full spectrum coverage from 200 Hz to over 3 GHz including infrared signals.

Monitor Mode

After a sweep, the alarm monitor (silent or audible alert) guards against new devices brought in or the remote control activation of surveillance devices.

Auxiliary Audio Input

Allows user to listen to telephones or lines for “hot mikes,” hook switch bypass “infinity transmitters” and other telephone bugs. Unknown wires and cables can be tested for wired microphones.

FILTER: Audio filter used to accentuate voice frequencies and remove noise.

MODE: Sets the unit to Search or Monitor function. Search is for performing a sweep with the audio Automatic Gain Control engaged, the Monitor Mode sets the Alarm and Record output to detect an intrusion.

ALERT: Selects either audible Tone beeper or Silent flashing LED output from Monitor Mode.

LOW BATTERY INDICATOR: Voltage indicator indicates approximately 10% remaining power.

STATUS DISPLAY: Shows unit operating conditions made by button selections.

GAIN: Adjusts the internal sensitivity of the Detector and Audio systems.

PROBE INPUT: Provides input and power for active probes and automatically selects the appropriate Probe or Auxiliary detector circuits.

PULSING SEGMENT: Indicates alarm trip point in the Monitor Mode and activates the Alarm and Remote output.

INPUT LEVEL: Bar graph indicates signal strength of Probe or Auxiliary inputs.

ALERT LED: Flashes Red when input level exceeds trip point of Monitor Mode.

THRESHOLD: Sets the trip point for the Monitor Mode.

GAIN: Controls the audio gain (volume) to the speaker or headphone output.

PHONES: Allow for silent headphone detection, disconnects the internal speaker.

Read More about this Professional Counter Surveillance Probe and Monitor Kit